Jump to content
Arduino.lk Community Sri Lanka
  • Announcements

    • Team Arduino.lk

      Arduino Stater Kit 2 එකක් දිනාගන්න.   11/13/2017

      arduino.lk community වෙත ඔබව සාදරයෙන් පිළිගනිමු. ඔබගේ ගැටළු අදහස් මෙහි පළකර Rs 3650.00 වටිනා Arduino Stater Kit 2 එකක් දිනාගන්න. ඔබ කල යුත්තේ Arduino, හා සම්බන්ධ අදහස්, ලිපි, කමෙන්ට් මෙහි පල කර මෙහි ඇති LeaderBoard එකේ පළමු තැනට පැමිණීමයි. සැම මාසකම අවසාන දින 11.55 PM හොදම Contributor තෝරනු ලැබේ
Navodh

relay Connect with 5v Relay Module

Recommended Posts

Quote

WARNING: Mishandling or incorrect or improper use of relays could result in

serious personal injury or DEATH

possible physical damage of the product

faulty operation

or create serious/dangerous hazards.

Please make sure that you read and understand how your relay/relay module board works, the voltage and current it is rated for, and the risks involved in your project BEFORE you even attempt to start putting it together. Seek professional and qualified assistance BEFORE you undertake ANY high power projects.

If you choose to follow the instructions in this tutorial, you do so at your own risk. I am not an electrician, and am not a qualified electrical engineer - so please do your research and seek advice BEFORE undertaking a project using a relay. Please check your connections and test them BEFORE turning the power on.

I accept no responsibility for your project, or the risk/damage/fire/shock/injury/death/loss that it causes. You take full responsibility for your actions/project/creation, and do so at YOUR OWN RISK !!!

Please note: It is illegal in some countries to wire up a high power project without an electrician. Please check your country's rules/laws/regulations before you undertake your project. If you have any doubts - don't do it.

What is a relay

A Relay is an electrically operated switch. Many relays use an electromagnet to mechanically operate the switch and provide electrical isolation between two circuits. In this project there is no real need to isolate one circuit from the other, but we will use an Arduino UNO to control the relay. We will develop a simple circuit to demonstrate and distinguish between the NO (Normally open) and NC (Normally closed) terminals of the relay. We will then use the information gained in this tutorial to make a much more exciting circuit. But we have to start somewhere. So let's get on with it.

Parts Required:

  • Arduino UNO compatible board
  • 4 Channel Relay Module
  • 2x LEDs
  • 2x 330 ohm resistors
  • Jumper Wires (male to male)
  • Jumper Wires (female to male)

Fritzing Sketch

Relay_LED_Circuit_with_Arduino.png

Table of Connections

Fritzing_TableOfConnections.png

Arduino Sketch

/* 
  Connect 5V on Arduino to VCC on Relay Module
  Connect GND on Arduino to GND on Relay Module 
  Connect GND on Arduino to the Common Terminal (middle terminal) on Relay Module. */
 
 #define CH1 8   // Connect Digital Pin 8 on Arduino to CH1 on Relay Module
 #define CH3 7   // Connect Digital Pin 7 on Arduino to CH3 on Relay Module
 #define LEDgreen 4 //Connect Digital Pin 4 on Arduino to Green LED (+ 330 ohm resistor) and then to "NO" terminal on relay module
 #define LEDyellow 12 //Connect Digital Pin 12 on Arduino to Yellow LED (+ 330 ohm resistor) and then to "NC" terminal on relay module
 
 void setup(){
   //Setup all the Arduino Pins
   pinMode(CH1, OUTPUT);
   pinMode(CH3, OUTPUT);
   pinMode(LEDgreen, OUTPUT);
   pinMode(LEDyellow, OUTPUT);
   
   //Provide power to both LEDs
   digitalWrite(LEDgreen, HIGH);
   digitalWrite(LEDyellow, HIGH);
   
   //Turn OFF any power to the Relay channels
   digitalWrite(CH1,LOW);
   digitalWrite(CH3,LOW);
   delay(2000); //Wait 2 seconds before starting sequence
 }
 
 void loop(){
   digitalWrite(CH1, HIGH);  //Green LED on, Yellow LED off
   delay(1000);
   digitalWrite(CH1, LOW);   //Yellow LED on, Green LED off
   delay(1000);
   digitalWrite(CH3, HIGH);  //Relay 3 switches to NO
   delay(1000);
   digitalWrite(CH3,LOW);    //Relay 3 switches to NC
   delay(1000);
 }

The Red light on the Relay board turns on when power is applied (via the VCC pin). When power is applied to one of the Channel pins, the respective green light goes on, plus the relevant relay will switch from NC to NO. When power is removed from the channel pin, the relay will switch back to NC from NO. In this sketch we see that power is applied to both LEDs in the setup() method. When there is no power applied to the CH1 pin, the yellow LED will be on, and the Green LED will be off. This is because there is a break in the circuit for the green LED. When power is applied to CH1, the relay switches from NC to NO, thus closing the circuit for the green LED and opening the circuit for the yellow LED. The green LED turns on, and the yellow LED turns off.

I also show what happens when you apply power to a channel (eg. CH3) when there is nothing connected to the relay terminals. The respective onboard LED illuminates. This is useful for troubleshooting the relays, and knowing what state the relay is in (NC or NO). NC stands for Normally closed (or normally connected) NO stands for Normally open (or normally disconnected)

 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


×